background image

GB - 8

Keep unit free of ice or other debris. Clean up oil or fuel 
spills.

This product is equipped with an internal combustion 
type engine. DO NOT use unit on or near any 
unimproved, forest-covered or brush covered land 
unless exhaust system is equipped with a spark 
arrester meeting applicable local, state or federal laws. 
A spark arrester, if it is used, must be maintained in 
effective working order by operator.

Fuel is highly flammable and its vapors are explosive. 
Handle with care. Use an approved fuel container.

NO smoking, NO sparks, NO flames. ALWAYS allow 
engine to cool before servicing.

NEVER fill fuel tank when engine is running or hot from 
operation.

NEVER fill or drain fuel tank indoors.

Replace fuel cap securely and clean up spilled fuel.

Never fill containers inside a vehicle or on a truck or 
trailer bed with a plastic liner. Always place containers 
on the ground away from your vehicle before filling.

When practical, remove gas-powered equipment from 
the truck or trailer and refuel it on the ground. If this is 
not possible, then refuel such equipment on a trailer 
with a portable container, rather than from a gasoline 
dispenser nozzle.

Keep the nozzle in contact with the rim of the fuel tank 
or container opening at all times until fueling is 
complete. Do not use a nozzle lock-open device.

If fuel is spilled on clothing, change clothing 
immediately.

Before tipping unit up onto housing, remove fuel so no 
spills will occur. Ensure unit is secure and will not tip 
over during maintenance. 

ALWAYS keep protective structures, guards, and 
panels in good repair, in place and securely fastened. 
NEVER modify or remove safety devices.

DO NOT change engine governor settings or 
over-speed engine. 

Fumes from engine exhaust can cause injury or death. 
DO NOT run engine in an enclosed area. Always 
provide good ventilation.

ALWAYS maintain unit in safe operating condition. 
Damaged or worn out muffler can cause fire or 
explosion.

Keep all hardware properly tightened. Check shear 
bolts frequently. 

Maintain or replace safety and instruction labels, as 
necessary.

NEVER store unit with fuel in fuel tank, inside a 
building where any ignition sources are present such 
as hot water heaters, space heaters, or clothes dryers. 
Allow the engine to cool before storing in any 
enclosure.

For extended storage, clean unit thoroughly. See 
Engine Manual for proper storage.

Use only attachments or accessories designed for your 
unit. 

Check components frequently. If worn or damaged, 
replace with manufacturer’s recommended parts.

Содержание Sno-Thro 939003-


























Отзывы: