background image

 

GB - 11

 

MAINTENANCE AND SERVICE 
SAFETY RULES

 

Before cleaning, removing clogs or making 
any inspections, repairs, etc.: disengage 
clutch(es), stop unit and engine, remove 
key, allow moving parts to stop. Allow hot 
parts to cool.

 

Before tipping unit up onto housing, remove 
enough fuel so no spills will occur. Ensure unit 
is secure and will not tip over during 
maintenance. 
ALWAYS keep protective structures, guards, 
and panels in good repair, in place and 
securely fastened. NEVER modify or remove 
safety devices.
DO NOT change engine governor settings or 
over-speed engine. 
Fumes from engine exhaust can cause injury 
or death. DO NOT run engine in an enclosed 
area. Always provide good ventilation.
ALWAYS maintain unit in safe operating 
condition. Damaged or worn out muffler can 
cause fire or explosion.

Keep all hardware properly tightened. Check 
shear bolts frequently.
Maintain or replace safety and instruction 
labels, as necessary.

 

STORAGE SAFETY RULES

 

NEVER store with fuel in fuel tank, inside a 
building where any ignition sources are 
present.
Allow engine to cool completely.
For extended storage, clean unit thoroughly. 
See Engine Manual for proper storage.

 

ACCESSORY AND ATTACHMENT 
SAFETY RULES

 

Use only attachments or accessories 
designed for your unit. 
Check components frequently. If worn or 
damaged, replace with manufacturer’s 
recommended parts.

 

Tools Required

 

• Pliers
• Open-End Wrenches: 3/8, 7/16, 1/2,

 9/16 in and/or Adjustable Wrench

• Tire Gauge

 

Handlebar

 

Unfold upper handlebar until it snaps into 
position on the lower handlebar.Tighten the 
handlebar knobs to secure.

 

Discharge Chute (932103, 310)

 

1. Grease discharge chute ring if not already 

greased (Figure 4a).

2. Remove mounting hardware and chute 

crank support from top of engine.

3. Slide discharge chute over opening on 

housing and under the retaining clip.

4. Position chute support bracket over studs.
5. Place the chute crank support on the 

studs, over the chute support bracket.

6. Secure chute crank and chute support 

brackets to studs with mounting hardware 
just removed.

 

NOTE: 

 

Make sure the discharge chute sits 

flush on the discharge chute ring before 
tightening hardware.

7. Insert the chute crank through the hole in 

chute crank support.

8. Remove the spring clip from the chute 

pinion gear, insert chute crank into pinion 
and secure with spring clip.

 

ASSEMBLY

 

WARNING: 

 

AVOID INJURY. Read 

and understand 

 

Assembly

 

 and 

 

Fuel 

Safety Rules

 

 before proceeding.

Содержание Sno-Thro 932102



























Отзывы: