Ariens 927067-10528 Скачать руководство пользователя страница 14

GB - 14

IMPORTANT: Proper maintenance can 
prolong the life of unit. The following chart 
shows the recommended service schedule. 
Refer to the maintenance instructions in the 
Engine Manual for additional information.
IMPORTANT: Do not place unit on end.

MAINTENANCE SCHEDULE

WARNING: AVOID INJURY. Read 
and understand the entire Safety 
section before proceeding.

Interval

Task

Action

Each Use

Check Safety 
Interlock System

WARNING: Safety interlock system failure and 
improper operation of unit can result in death or 
serious injury. Test this system each time the unit 
is operated. If this system does not function as 
described, do not operate until repairs are made 
(see Safety Interlock System on page 10).

Check Parking 
Brake

Engage parking brake and engage transmission bypass 
lever (see MOVING THE UNIT MANUALY on page 12). 
Push unit. If unit rolls, contact your Ariens Dealer.

Clean Unit

Clean engine, battery, seat, mower deck, etc. of all dirt and 
debris. Do not use solvents, hard cleaners, or abrasives. 
NOTE: Protect painted surfaces with automotive type wax.
IMPORTANT: The electric clutch MUST be cool prior to 
cleaning mower deck with water.

Check Tires

See SPECIFICATIONS on page 24 for correct tire 
pressure.

Check Mower 
Blade

Check for a worn or damaged mower blade (see 
SHARPENING MOWER BLADE on page 18).

Follow Engine 
Manual 
Maintenance 
Schedule

Perform scheduled engine maintenance. Refer to Engine 
Manual for detailed instructions.

25 Hours 

or Every 

Season

Check Battery

Keep battery and battery terminals clean (see Cleaning 
Battery and Battery Cables
 on page 19).

Lubricate Unit

Apply grease to two front 
wheel zerks, steering 
gear, and pinion.

50 Hours 

or Every 

Season

Check Fasteners

Check mower blade mounting hardware and all other 
fasteners. Replace fasteners that are missing or damaged. 
Tighten all nuts and bolts to the correct torque value.

100 Hours 

or Every 

Season

Check All Belts

Replace worn or deteriorated belts.

• Check hydrostatic belt (see HYDROSTATIC BELT 

REPLACEMENT on page 20 for hydrostatic belt 
location).

• Check PTO belt (see PTO BELT REPLACEMENT on 

page 21 for PTO belt location).

Zerk

Steering 
Gear and 
Pinion

Zerk

Содержание 927067-10528



























Отзывы: