background image

9

BREAKING IN YOUR TILLER

Break-in your belt(s), pulleys and tine control before you 
actually begin tilling.
• 

Start engine, tip tines off ground by pressing handles 
down and engage tine control to start tine rotation. 
Allow tines to rotate for five minutes.

• 

Check tine operation and adjust if necessary.  See “TINE 
OPERATION CHECK” in the Service and Ad just ments 
sec tion of this manual.

TILLING HINTS 

CAUTION:  Until you are accustomed 
to handling your tiller, start ac tu al field 
use with throttle in slow position. 

To help tiller  move forward, lift up the handles slightly (thus 
lifting depth stake out of ground). To slow down the tiller, 
press down on handles.

If you are straining or tiller is shaking, the wheels and depth 
stake are not  set properly in the soil being tilled. The proper 
setting of the wheels and depth stake is through trial and 
error and depends upon the soil con di tion.  (The harder or 
wetter the ground, the slower the engine and tine speed 
needed. Under these poor con di tions, at fast speed the 
tiller will run and jump over the ground). 

 A properly adjusted tiller will dig with little effort from the 
operator.
• 

Tilling is digging into, turning over, and breaking up 
packed soil before planting.  Loose, unpacked soil helps 
root growth. Best tilling depth is 4"-6".  A tiller will also 
clear the soil of unwanted vege ta tion. The de com po si tion 
of this vegetable mat ter en rich es the soil.  De pend ing 
on the climate (rain fall and wind), it may be advisable 
to till the soil at the end of the growing season to further 
condition the soil.

• 

Soil conditions are important for proper tilling. Tines will 
not readily penetrate dry, hard soil which may con trib ute 
to excessive bounce and difficult handling of your tiller. 
Hard soil should be mois tened before tilling; however, 
extremely wet soil will “ball-up” or clump during tilling. 
Wait until the soil is less wet in order to achieve the 
best results. When tilling in the fall, remove vines and 
long grass to prevent them from wrapping around the 
tine shaft and slowing your tilling operation.

• 

You will find tilling much easier if you leave a row 
untilled between passes. Then go back between tilled 
rows. (See Fig. 9) There are two reasons for doing 
this. First, wide turns are much easier to negotiate than 
about-faces. Sec ond, the tiller won’t be pulling  itself, 
and you, toward the row next to it.

• 

Set depth stake and wheel height for shallow tilling 
when working extremely hard soil or sod. Then work 
across the first cuts at normal depth.

3

2

1

5

4

6

7

Fig. 9

CULTIVATING

Cultivating is destroying the weeds between rows to pre-
 vent them from robbing nourishment and moisture from the 
plants. At the same time, breaking up the upper layer of 
soil crust will help retain moisture in the soil. Best digging 
depth is 1"-3".
• 

You will probably not need to use the depth stake. Begin 
by tipping the depth stake forward until it is held by the 
stake spring.

• 

Cultivate up and down the rows at a speed which will 
allow tines to uproot weeds and leave the ground in 
rough con di tion, promoting no fur ther growth of weeds 
and grass (See Fig. 10).

Fig. 10

OPERATION

6.  After starting the engine, gradually open choke by 

turning the choke lever and finally keep it fully opened. 
Do not fully open the choke lever immediately when 
the engine is cold or the ambient temperature is low, 
because the engine may stop.

NOTE:

 If engine does not start, see trou ble shoot ing points.

Fig. 8

THROTTLE 

CONTROL

ENGINE 
SWITCH

CHOKE 
CON TROL

FUEL VALVE

RECOIL 

STARTER

SPARK 
PLUG

Содержание 902032

































































Отзывы: