manualshive.com logo in svg

ARI ARI-PACO 2G, Инструкции по эксплуатации и монтажу

Поделиться
Скачать
ARI ARI-PACO 2G Скачать руководство пользователя страница 50

- Translated original instructions -

0040501006 2422

Page 2-50

Operating and installation instructions

Thrust actuator ARI-PREMIO

®

-Plus 2G

11.0  Disposal

The devices described in these instructions are to be recycled.
According to Directive 2012/19/EU on waste from electrical and electronic 
equipment (WEEE), these may not be disposed of by means of municipal waste 
disposal companies.
For the benefit of environmentally friendly recycling, the devices can be returned 
to the supplier within the EU or returned to a locally approved disposal company. 
Observe the regulations applicable in your country.

12.0  Warranty / Guarantee

The extent and period of warranty cover are specified in the "Standard Terms and Conditions of 
Albert Richter GmbH & Co. KG“ valid at the time of delivery or, by way of departure, in the contract 
of sale itself.
We guarantee freedom of faults in compliance with state-of-the-art technology and the confirmed 
application.
No warranty claims can be made for any damage caused as the result of incorrect handling or 
disregard of operating and installation instructions, datasheets and relavant regulations.
This warranty also does not cover any damage which occurs during operation under conditions 
deviating from those laid down by specifications or other agreements.
Justified complaints will be eliminated by repair carried out by us or by a specialist appointed by us.
No claims will be accepted beyond the scope of this warranty. The right to replacement delivery is 
excluded.
The warranty shall not cover maintenance work, installation of external parts, design modifications 
or natural wear.
Any damage incurred during transport should not be reported to us but 

rather 

to the competent 

cargo-handling depot, the railway company or carrier company immediately or else claims for 
replacements from these companies will be invalidated.

ARI-Armaturen Albert Richter GmbH & Co. KG, D-33750 Schloß Holte-Stukenbrock

Telephone (+49 5207) 994-0 Telefax (+49 5207) 994-158 or 159

Internet: https://www.ari-armaturen.com    E-mail: [email protected]

Содержание ARI-PACO 2G





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды