Argus RSM 48 UPF Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 58

background image

When REMOTE ADJUST is enabled it is possible to adjust the RSM remotely. The UP, DOWN,
ENTER

commands are equivalent to physically pressing the keys on the front panel of the module

itself.

To change the status of REMOTE ADJUST ACCESS/LOCKOUT, select the REMOTE COMMUNI-
CATIONS

menu item. You will be prompted for the security code before any adjustments can be

performed.

REMOTE ADJUST ACCESS/LOCKOUT

is the second item inside the REMOTE COMMUNICA-

TIONS

menu. Pressing the Enter/Select key toggles between REMOTE ACCESS and REMOTE

LOCKOUT

.

8.2

Module ID

In order for the module to be identified for remote communication each module must be assigned
an unique identification number. Sequentially program each module in the system. Do not duplicate
the ID number on separate shelves. Select the MODULE I.D. entry mode via the REMOTE AC-
CESS

sub menu. The default address or programmed address will be displayed. Using the Up and

Down

keys increase or decrease the number displayed. The digits will wrap around ie. when the

number 99 is reached, pressing the Up key will cause the number to jump to 01. Press Enter/Se-
lect

to enter the desired number. The unit will display RETURN. If two modules have the same ID#

a line conflict will occur which will result in garbled communications.

8.3

Baud Rate

The unit has four programmable baud rate settings for use with the Serial Communications Inter-
face. Using the cursor controls the operator scrolls between 1200, 2400, 4800 and 9600 Baud
transmission rates. When the appropriate rate is chosen to match the external communications de-
vice (ie modem.) the operator presses the Enter/Select key.

8.4

Remote Disable

Remote access via the serial communications interface can be disabled if programmed. Disabling
the feature will inhibit remote interrogation of the unit.

8.5

Remote Adjust Disable

Depending on factory programming some units are able to receive remote adjustment of all levels
similar to local operation. Consult factory for complete information on the operation of this feature.

ARGUS TECHNOLOGIES

010-030-C0 Rev E Page 41 of 42

«
...
53
54
55
56
57
...
»

Содержание RSM 48 UPF



























































Отзывы:

Нет отзывов

Похожие инструкции для RSM 48 UPF

SACE Tmax XT Series

Бренд: ABB Страницы: 11

Бренд: ABB Страницы: 6

Бренд: LANGER EMV-Technik Страницы: 25

Electric Clamshell CSE12-208VCD

Бренд: Lang Страницы: 16

Бренд: TDX Tech Страницы: 27

Бренд: 7starlake Страницы: 52

Бренд: Giovenzana Страницы: 46

Бренд: CMD Страницы: 6

Бренд: Wachs Страницы: 24

Бренд: Vestil Страницы: 4

Allen-Bradley 6200P-NS3A1

Бренд: Rockwell Automation Страницы: 28

Бренд: Omron Страницы: 24

Mini Filter Wheel with OAG

Бренд: Starlight Xpress Страницы: 7

Бренд: MRMC Страницы: 66

OPTIM 9 P&P-225-440

Бренд: Circutor Страницы: 40

Crowcon Xgard S011843

Бренд: Halma Страницы: 2

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды