Argus PiCUS Tree Motion Sensor Online Скачать руководство пользователя страница 24

Страница: 24 / 83

PiCUS TMSO Manual

4.3 Configuring the Telephone App

4.3.1 Install TMSO.App on the Mobile Phone

You can easily download and install the TMSO.App from the App Store on your mobile phone.

TMSO.App

4.3.2 Configure Authentication Code

The authentication code is a security measure to ensure that no one but the owner of a PTMSO
can connect to and control it.

Your personal authentication code can be found on the supplied USB stick in the file

AuthenticationTMSO.txt

CAUTION!

Keep your authentication code secret!

Start the TMSO.App installed on your
mobile phone.

II.

In the main menu of the app, click on
the

Authentication

menu item.

III.

In the following menu, the

Current Code

line shows the currently set authentication
code.

IV.

In the

Change Code

line, enter your code

and save it by clicking on the diskette
symbol in the upper right corner.

III

Содержание PiCUS Tree Motion Sensor Online




















































































Результаты поиска

Содержание PiCUS Tree Motion Sensor Online

Отзывы:

Похожие инструкции для PiCUS Tree Motion Sensor Online

Бренды по названию

Популярные бренды

Argus PiCUS Tree Motion Sensor Online, Руководство по оборудованию

Результаты поиска

Содержание PiCUS Tree Motion Sensor Online

Отзывы:

Похожие инструкции для PiCUS Tree Motion Sensor Online

Бренды по названию

Популярные бренды