Argox AI-68 Series Скачать руководство пользователя

Страница: 149 / 159

141

5.2

Bar code issues

My scanner doesn

’

t read the bar code

properly.

￭

Reset your scanner.

￭

Check the quality of your bar codes.
Wrinkled, smudged, blurred or torn bar
codes won’t be read by your scanner.

￭

The reading window of your scanner may
be dirty and block the field of view. Clean
the reading window.

The data isn

’

t sent to my computer.

￭

Did you establish the connection between
your scanner and cradle?

￭

Did your scanner connect to other
Bluetooth device?

￭

Make sure the USB cable is tightly plugged
into your cradle and computer.

￭

Your scanner is connecting to another
cradle. Break their connection and
connect your scanner to your cradle.

My scanner doesn

’

t decode the bar code,

but the bar code type is supported.

￭

Did you turn on Read for the bar code
type?

￭

The density of your bar code may be too
high for your scanner to decode.

Содержание AI-68 Series
































































































































































Результаты поиска

Содержание AI-68 Series

Отзывы:

Похожие инструкции для AI-68 Series

Бренды по названию

Популярные бренды

Argox AI-68 Series, Руководство пользователя

Результаты поиска

Содержание AI-68 Series

Отзывы:

Похожие инструкции для AI-68 Series

Бренды по названию

Популярные бренды