Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 477 / 535

background image

7-109

7

Servicing ACT Shock

REMOVING/CLEANING

1. Remove the shock from the snowmobile.

2. Wash the shock body in parts-cleaning solvent; then

dry with compressed air to remove sand and dirt.

DISASSEMBLING

1. Remove the screw from the pressure valve assembly

on the bottom of the shock. Discharge all the pres-

sure from the shock using the Inflation Needle. Open

the valve in filler handle until all pressure is released.

FS250

FS251

2. Using a 1-in. wrench, loosen the bearing assembly

and remove the shock rod and valve assembly from

the shock body.

FS252

FS055

3. Pour the oil from the shock body into a suitable con-

tainer.

4. Remove the pressure valve assembly. Account for

the O-ring.

FS253

5. Using Floating Piston Removal Tool, remove the

floating piston.

FS254

! WARNING

Before any service is performed on the gas shock
absorber, first discharge all pressure from the shock
remote reservoir. Remove the valve screw from the
pressure valve and insert the Inflation Needle. Open
valve until all pressure is released. Failure to do this
may cause personal injury.

! WARNING

When using compressed air to dry components,
always wear safety glasses.

Manual

Table of Contents

«
...
475
476
477
478
479
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренд: Yamaha Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды