Arctic Cat Sno Pro 120 2011 страница 348 Скачать руководство пользователя | Manualshive

Страница: 348 / 535

background image

6-25

6

MS519

MS340

13. Using an appropriate seal removing tool, remove the

ring gear seal from the gear case.

CLEANING AND INSPECTING GEAR
CASE (w/o Reverse)



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Wash the gear case halves and unsealed bearings in

parts-cleaning solvent.

2. Inspect the gear case halves for trueness, scoring, pit-

ting, scuffing, or any imperfections in the casting.

3. Inspect all threaded areas for damaged or stripped

threads.

4. Inspect the bearing areas for cracks or excessive

bearing movement. If evidence of excessive bearing

movement is noted, replace the component.

5. Inspect the bearings for wear, scoring, scuffing, dam-

age, or discoloration. Rotate the bearings. Bearings

must rotate freely and must not bind or feel rough. If

any abnormal condition is noted, replace the bearing.

6. Inspect the planetary and ring gears for wear, cracks,

or chipped teeth.

7. Apply a light film of Arctic Cat ACT Drive Fluid to

the unsealed bearings prior to assembling.

ASSEMBLING GEAR CASE
(w/o Reverse)

1. Using an appropriate seal installation tool, install the

oil seal into the output shaft opening of the gear case;

then install the inner retaining ring into the groove of

the gear case.

MS521

2. Using a suitable bearing press, install the bearing

onto the output shaft of the ring gear.

MS522



NOTE: When pressing the bearing onto the output

shaft of the ring gear, use an insert that is the same
diameter as the bearing dish of the ring gear.

MS523

3. Using a suitable press, install the ring gear assembly

to the gear case.

CAUTION

Always use a proper insert or thread a cap screw into
the end of the output shaft of the ring gear when remov-
ing the bearing or component damage will occur.

Manual

Table of Contents

«
...
346
347
348
349
350
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренд: Yamaha Страницы: 90

Formula 500 1998

Бренд: Ski-Doo Страницы: 398

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды