background image

39

6. Apply red Loctite #271 to the threads

of the cap screw; then tighten the nut

to 45 ft-lb (61.2 N-m).

7. Place the cotter pin into the ski cap

screw and spread the pin.

8. Repeat procedure for the other ski.

Rail Wear Strips

Arctic Cat recommends that the wear

strips be checked weekly and replaced as

necessary. Measure the wear strips at

25.4 cm (10 in.) intervals. Wear strips

must be 10.7 mm (0.42 in.) thick or

thicker. 

0745-807

If wear strip measurements are less than

specified, replacement of both wear strips

is necessary to prevent premature track

clip wear and possible track damage.

Take the snowmobile to an authorized

Arctic Cat Snowmobile dealer for this

service. This service is at the discretion

and expense of the snowmobile owner.
Each time a new set of wear strips are

installed, they should be tempered. Tem-

per the wear strips by driving the snow-

mobile for approximately one mile (1.6

km) on a hard pack trail; then immedi-

ately drive into deep snow and allow the

wear strips to cool. Repeat the procedure

(warming up the wear strips; then cooling

them down) two or three times.

NOTE: The rail wear strips will

wear rapidly if the snowmobile is

operated on terrain on which the

snow cover is minimal. Loose snow

is required to cool and lubricate the

wear strips and prevent accelerated

wear.

NOTE: If operating on ice or hard-

packed snow conditions, it is recom-

mended that Ice Scratchers (p/n

5639-897) be installed to reduce wear

strip wear and engine overheating.

Содержание 2262-967



















































Отзывы: