Arcteq AQ-G215 Скачать руководство пользователя страница 54

Страница: 54 / 458

5 Functions

5.1 Functions included in AQ-G215

The AQ-G215 generator protection relay includes the following functions as well as the number of

stages in those functions.

Table. 5.1 - 4. Protection functions of AQ-G215.

Name (number

of stages)

IEC

ANSI

Description

NOC (4)

I>>

I>>>

I>>>>

50/51

Non-directional overcurrent protection

DOC (4)

Idir>

Idir>>

Idir>>>

Idir>>>>

Directional overcurrent protection

NEF (4)

I0>

I0>>

I0>>>

I0>>>>

50N/51N

Non-directional earth fault protection

DEF (4)

I0dir>

I0dir>>

I0dir>>>

I0dir>>>>

67N/32N

Directional earth fault protection

OV (4)

U>>

U>>>

U>>>>

Overvoltage protection

UV (4)

U<<

U<<<

U<<<<

Undervoltage protection

NOV (4)

U0>

U0>>

U0>>>

U0>>>>

59N

Neutral overvoltage protection

FRQV (8)

f>>

f>>>

f>>>>

f<<

f<<<

f<<<<

81O/81U

Overfrequency and underfrequency protection

ROCOF (1)

df/dt>/< (1…8)

81R

Rate-of-change of frequency

CUB (4)

I2>

I2>>

I2>>>

I2>>>>

46/46R/46L

Negative sequence overcurrent/

phase current reversal/

current unbalance protection

VUB (4)

U1/U2>/<

U1/U2>>/<<

U1/U2>>>/<<<

U1/U2>>>>/<<<<

47/27P/59PN

Sequence voltage protection

Q-G215

-G215

Instruction manual

Version: 2.04

Содержание AQ-G215










































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды

Arcteq AQ-G215, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-G215

Отзывы:

Похожие инструкции для AQ-G215

Бренды по названию

Популярные бренды