ARCO St.Moritz PC10 страница 58 Скачать руководство пользователя

Страница: 58 / 68

19-CLEANING

REMEMBER THAT ONLY A CORRECTLY POSITIONED AND CLEAN BRAZIER CAN GUARANTEE IGNITION AND OPTIMAL

OPERATION OF YOUR PELLET PRODUCT. IN CASE OF FAILED IGNITION AND AFTER ANY OTHER LOCK STATE OF THE

PRODUCT, IT IS ESSENTIAL TO EMPTY THE BRAZIER BEFORE EVERY RESTART

For the brazier to be cleaned properly, remove it from its housing completely and thoroughly clean all the holes and the grate on the

bottom. If good quality pellets are used, you will normally only need to use a brush to restore the optimal operating conditions of the

component.

Ash pan cleaning

Remove and empty the “U” ash tray. Wipe away any residual ash before reinserting the pan. Your experience and the quality of the pellets

will determine the ash tray cleaning frequency. However, it is recommended not to exceed 2 or 3 days.

CLEANING THE GLASS

It is recommended to clean the ceramic glass with a dry brush, or if it is very dirty, spray a little specific detergent and clean with a cloth.

ATTENTION!

Do not use abrasive products and do not spray the glass cleaning product on the painted parts and on the door

gaskets (ceramic fibre cord).

CLEANING THE AIR FILTER

A wire mesh air filter is found at the back of the stove, whose purpose is to prevent dirt entering the motor body and the internal sensor.

It is recommended to check that the filter is clean every 15/20 days. If needed remove fluff or the material that has deposited on it.

Inspection and cleaning are required more frequently if there are pets in the house.

Simply remove the filter to clean. To clean it use a brush or a damp cloth or compressed air. Set it back in place by simply pressing it

(interlocks).

The filter is made of metallic mesh and is soft and flexible to the touch therefore, when cleaning, be careful not to

crush or damage it. In the event of breakage it must be replaced.

ATTENTION!

Never let the stove work without the air filter fitted. MCZ cannot be held liable for any damage caused to the internal

components if this requirement is not complied with.

Содержание St.Moritz PC10




































































Результаты поиска

Содержание St.Moritz PC10

Отзывы:

Похожие инструкции для St.Moritz PC10

Бренды по названию

Популярные бренды

ARCO St.Moritz PC10, Руководство по установке

Результаты поиска

Содержание St.Moritz PC10

Отзывы:

Похожие инструкции для St.Moritz PC10

Бренды по названию

Популярные бренды