manualshive.com logo in svg

ARCIMOTO FUV 2022, Руководство пользователя

Поделиться
Скачать
ARCIMOTO FUV 2022 Скачать руководство пользователя страница 63

DISPLAY

Display

The FUV features a touch- sensitive color Display that
provides useful information regarding the current state of
the FUV.

The touch options on the Display allow you to turn the
FUV ON and OFF, change the PIN assigned to the FUV,
and to enable Extended Range Mode.

NOTE

Remove the clear protective film from the Display before use.

Display: OFF State

When the FUV is OFF, the Display is black. Turn the FUV
ON via either the Key or by using the PIN keypad on the
Display as described below.

Turning the FUV ON via the Display

1. Press anywhere on the Display to invoke the Enter

PIN keypad.

2. Enter the 6-digit PIN assigned to the FUV.

FUV Owner's Manual (REV 0)  • last revised: 3/31/2022 • part# 006290  •  doc ID: P10001

page 61

Содержание FUV 2022



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды