manualshive.com logo in svg

ARCIMOTO FUV 2022, Руководство пользователя

Поделиться
Скачать
ARCIMOTO FUV 2022 Скачать руководство пользователя страница 54

page 52

FUV Owner's Manual (REV 0) • last revised: 3/31/2022 • part# 006290  •  docID: P10001

NOTE

If the motor OFF switch is activated, the FUV must first be set
to Neutral, and then into the direction you wish to proceed
before resuming to drive.

Brake Pedal

The Brake Pedal is on the driver's right foot well. It
controls the hydraulic brakes on all three wheels.

Use the Brake pedal to decelerate quickly, and bring the
FUV to a full stop.

Press the Brake Pedal While Starting the FUV

As a safety feature, the FUV will not start unless the
Brake Pedal is fully depressed.

NOTE

Practice braking in a safe area to become familiar with the feel
of the brakes before driving in traffic. Practice is strongly
recommended to perfect safe emergency stops.

l

When braking, the throttle should be in the closed
(OFF) position.

l

Never rest your foot on the Brake pedal while
driving. This can cause the braking system to
overheat. This increases the stopping distance and
can cause the brake system to fail.

CONTROLS

Содержание FUV 2022



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды