manualshive.com logo in svg

ARCIMOTO FUV 2022, Руководство пользователя

Поделиться
Скачать
ARCIMOTO FUV 2022 Скачать руководство пользователя страница 163

STORAGE

Storage

Vinyl graphics and paint are degraded by prolonged
exposure to sun and atmospheric pollutants. Whenever
possible, store the FUV in a garage or in a shaded area
during the day.

At night, protect the FUV from dew or rain, which may
contain

acidic

pollutants

(particularly

in

large

metropolitan areas). When a garage is not available,
consider using a cloth cover at night.

Note that Arcimoto offers canvas FUV covers that are
perfect for protecting your FUV (see the

Optional

Accessories section on page 169

).

Storage Mode: Overview

This section describes how to properly put the FUV into
Storage Mode.

Follow these instructions any time that the FUV will be
stored for more than one week.

If the FUV is stored without following these instructions,
the HV Batteries could drain to the point that the FUV will
not start when taken out of storage.

Note that when the FUV is used on a daily or semi-daily
basis, simply plugging the FUV into a charging station will
keep the HV batteries charged and ready to use.

However, leaving the FUV connected to a charging

station for more than one week may lead to accelerated
wear on the HV Batteries. This is because the ideal state of
charge for HV Batteries is between 30% and 60%. Leaving
the FUV at full charge for an extended period of time
(more than one week) leads to premature wear on the
HV Batteries.

Storage Requirements

The FUV must be stored in a environment where the
ambient air temperature is within the following range:

25° F to 140° F (-4° C to 60° C)

FUV Owner's Manual (REV 0)  • last revised: 3/31/2022 • part# 006290  •  doc ID: P10001

page 161

Содержание FUV 2022



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды