manualshive.com logo in svg

Archgard 45-DVFE28LN-1, Инструкция по установке, эксплуатации и обслуживанию, Страница: 7 / 68

Поделиться
Скачать
Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 7

7

Installation

5.0  Installation Checklist

This standard installation checklist is to be used by the installer in conjunction with, not instead of, the instructions contained 

within this installation manual.

Customer:

Date Installed:

Install Address:

Location of Fireplace:

Installer:

Appliance Install: (Section 9.0)

YES

IF NO, WHY NOT?

Fireplace is leveled and secured.

Venting: (Section 10.0)

YES

IF NO, WHY NOT?

Venting configuration complies with vent diagrams.
Venting installed and secured in place maintaining proper clearances.

Maintained 1/4" rise for every 1 ft. on horizontal run.

Terminations installed and sealed in compliance with local building code.
Direct vent termination is highest point in vent assembly.

Wiring / Electrical: (Section 7.0)

YES

IF NO, WHY NOT?

Connected to household 110/120v per local codes.
Unit is properly grounded.

Gas: (Section 13.0)

YES

IF NO, WHY NOT?

Proper appliance for fuel type?
Was a conversion performed?
Leak check performed & inlet and manifold pressures verified?
Verified proper air shutter setting?

Finishing (Section 12.0):

YES

IF NO, WHY NOT?

Clearances meet installation manual requirements.

Appliance Setup:

YES

IF NO, WHY NOT?

Burner media / log set, glass door, and screen installed according to install 

manual.
Manual given to home owner.
Did you check operation of fans and flame modulation?

Comments:

Содержание 45-DVFE28LN-1





































































Отзывы:

Нет отзывов