manualshive.com logo in svg

Archgard 45-DVFE28LN-1, Инструкция по установке, эксплуатации и обслуживанию, Страница: 51 / 68

Поделиться
Скачать
Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 51

51

Maintenance

18.8  Replacing the Control Board

Before you begin:

• 

Ensure the fireplace is off and cool before servicing

• 

Disconnect power supply to the fireplace (including 

backup batteries)

• 

Turn off gas supply

• 

Open the Control Access Door (see 

Section 6.4

)

• 

The Control Board is attached to the bottom of the pedestal 

using velcro. Pull the Control Board outward to remove

CAUTION:

 Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous 

operation. Verify proper operation after servicing. This appliance, when installed, must be electrically grounded in accordance with 

local codes or, in the absence of local codes, with the 

National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical code, 

CSA C22.1

.

1. 

Mark all the wires connected to the control board as you 

unplug them from the control board.

2. 

Make sure you pull the 2-pin connector as shown in 

Figure 

18.8.02

.

3. 

Plug the wires and the 2-Pin connector into the new control 

board.

4. 

Place the new control board on the bottom of the pedestal by 

aligning the velcro on the control board with the velcro on the 

bottom of the pedestal.

Note:

 Keep wires tidy and organized away from the firebox when 

placing the control board back inside the pedestal.

Figure 18.8.01:

Final steps:

• 

Resupply gas to the fireplace

• 

Resupply power to the fireplace

• 

Light the fireplace and check for operation and flame 

appearance. See 

Section 17

 and 

Section 18.5

.

Figure 18.8.02:

Содержание 45-DVFE28LN-1





































































Отзывы:

Нет отзывов