Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 68

Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 49

49

Maintenance

18.5 Adjusting the Primary Air

The

45-DVFE28LN-1

includes an air shutter located under the door of the fireplace which may be used to adjust the primary air to

achieve the ideal flame as shown in

Figure 18.5.01

. To adjust, loosen the wing nut on the air shutter and adjust as shown in

Figure

18.5.02

. To open the air shutter and increase air flow to the burner, slide the air shutter to the left. To close the air shutter and decrease

air flow to the burner, slide the air shutter to the right.

CAUTION:

Do not adjust primary air below specified opening on the rating label.

Figure 18.5.01:

Lazy yellow flames

Ideal

Short blue flames

Air shutter open too far

Dark orange flames / black tips

Air shutter closed too far

Excessive burner media

Lifting (ghosting) flames

Improper Venting

Gas pressure too high

Figure 18.5.02: Air Shutter Adjustment Wingnut (as viewed from

underneath the firebox).

Open

Close

«
...
47
48
49
50
51
...
»

Содержание 45-DVFE28LN-1





































































Отзывы:

Нет отзывов