manualshive.com logo in svg

Archgard 45-DVFE28LN-1, Инструкция по установке, эксплуатации и обслуживанию, Страница: 48 / 68

Поделиться
Скачать
Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 48

48

Maintenance

18.2  Servicing Under Warranty

All service work under warranty must be conducted by a qualified Archgard service technician. Before servicing, read the terms and 

conditions of the warranty at the back of this manual. Contact the authorized Archgard dealer where you purchased the appliance from 

and provide them with details of the problem, along with the initial installation information (from the front of this manual).  

WARNING: 

Servicing of this appliance 

must be conducted by a qualified Archgard service technician

. Improper servicing, 

adjustment or alteration of this appliance may cause property damage, personal injury or loss of life. All servicing should 

be conducted with the appliance cold. All replacement parts must be authorized by Archgard for suitability.

18.3  Checking Inlet and Outlet Pressure

1. 

Remove the surround.

2. 

The pressure test taps are located on the valve's front face. The inlet is marked "

IN

" and the outlet is marked "

OUT

". See 

Figure 

18.3.01

. 

3. 

Loosen the set screw inside the tap with a 3/16" flathead screwdriver.

4. 

Connect a 1/4” (6 mm) rubber tube to the tap post and a manometer.

5. 

Verify that the readings obtained are within specs (as shown on the appliance rating label)

6. 

Be sure to tighten the set screw inside the tap after you have finished taking pressure readings.

7. 

Check for leaks.

18.4  Checking and Adjusting Pilot

The flame should not have yellow tips but should engulf the flame 

sensor and spark electrode. It can be adjusted be turning the screw 

marked “pilot” on the control valve (See 

Figure 18.3.01

).

It may be necessary to remove the pilot cover for a better view of the 

pilot flame (see next page).

The pilot flames should have the characteristics shown in 

the illustration to the right.

Figure 18.3.01

Figure 18.4.01

Figure 18.4.02

IN

PILOT

OUT

Содержание 45-DVFE28LN-1





































































Отзывы:

Нет отзывов