manualshive.com logo in svg

Archgard 45-DVFE28LN-1, Инструкция по установке, эксплуатации и обслуживанию, Страница: 43 / 68

Поделиться
Скачать
Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 43

43

Operation

Initializing the System for Handheld / Wall Mount Remote Operation

1. 

Connect IFC Control Module to AC power supply. A single beep will indicate the presence of power. 

NOTE: This will initiate Pilot 

Start-up in Manual Mode. The pilot will spark repeatedly and ignite if gas has been supplied to the unit

. 

Sync the control 

board to the remote to turn main burner and pilot off using the steps below.

2. 

The ON/OFF Override Jumper on the control board must be connected.

3. 

Press and hold th red SW1 button until the IFC module beeps three (3) times and/or the amber LED illuminates indicating the 

module is ready to synchronize with the remote.

4. 

Within ten (10) seconds push the ON/OFF key on the remote. The IFC module will beep four (4) times to indicate that it has 

successfully synced with the remote. Turn the fireplace OFF using the ON/OFF button on the remote to complete initialization. The 

remote will now control the fireplace.

5. 

Install the provided four (4) AA batteries into battery back up holder.

Turn ON the Appliance

With the system OFF, press the ON/OFF Key on the Remote. 

The Remote display will show other active icons on the screen. 

At the same time the Receiver will activate the appliance. 

A single beep from the receiver will confirm reception of the 

command.

Figure 17.5.04:

Figure 17.5.05:

Turn OFF the Appliance

With the system ON, press the ON/OFF Key on the Remote. 

The Remote display will show the current room temperature. At 

the same time the Receiver will turn the appliance off. A single 

beep from the receiver will confirm reception of the command.

Battery Compartment

Proflame II IFC Module

Содержание 45-DVFE28LN-1





































































Отзывы:

Нет отзывов