Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 41

Страница: 41 / 68

Operation

IMPORTANT

The Proflame II Remote is an integrated part of the Proflame II System, which consists of a Proflame II Remote, to be used in

conjunction with Integrated Fireplace Control (Proflame II Control Module).

The Proflame II Remote provides for controlling the following hearth appliance functions:

Main Burner ON/OFF

Main Burner flame modulation (6 levels)

Choice of Continuous Pilot on Demand or intermittent pilot (CPI/IPI)

Manual, Thermostat, and SMART thermostat functions

Comfort fan speed modulation (6 levels)

The Proflame II Remote uses a streamline design with a simple button layout and informative LCD display. A Mode Key is provided to

index between the features and a Thermostat Key is used for on/off or to index through the thermostat function. Additionally a Key Lock

function is provided.

ATTENTION

•

TURN OFF THE MAIN GAS SUPPLY DURING INSTALLATION OR MAINTENANCE OF THE RECEIVER DEVICE

•

TURN OFF MAIN GAS SUPPLY TO THE APPLIANCE PRIOR TO REMOVING OR REINSERTING THE BATTERIES

•

IN CASE OF REMOTE CONTROL MALFUNCTION TURN OFF THE FIREPLACE BY REMOVING POWER SUPPLY

(INCLUDING BACKUP BATTERIES)

•

FOR INSTALLATION/MAINTENANCE SWITCH OFF THE FIREPLACE BY REMOVING POWER SUPPLY (INCLUDING

BACKUP BATTERIES)

Technical Data - Remote Control

Supply Voltage

4.5 V (three (3) 1.5V AAA batteries

Ambient temperature ratings 0 - 50°C (32 - 122°F)
Radio Frequency

315 MHz

17.5 Remote Control Operation

Figure 17.5.01

Содержание 45-DVFE28LN-1





































































Результаты поиска

Содержание 45-DVFE28LN-1

Отзывы:

Archgard 45-DVFE28LN-1, Инструкция по установке, эксплуатации и обслуживанию, Страница: 41 / 68

Результаты поиска

Содержание 45-DVFE28LN-1

Отзывы: