manualshive.com logo in svg

Archgard 45-DVFE28LN-1, Инструкция по установке, эксплуатации и обслуживанию, Страница: 32 / 68

Поделиться
Скачать
Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 32

32

Installation

15.2  Reflective Glass Installation

The following steps highlight the procedure for installing the Reflective Ceramic Glass liner. We recommend using clean cotton gloves 

when handling panels. Handle the panels with care as they are delicate. Inspect the panels to ensure that no damage has occurred 

inside the package. Please report any damage immediately to your Authorized Archgard Dealer. Clean each panel with a soft cloth as 

you install them to remove any fingerprints as high temperatures can bake these prints on permanently.

Before you begin:

•  Ensure the gas supply is turned OFF and disconnect the power supply (including backup batteries)

• 

Open the Glass Door with Barrier Screen attached (see 

Section 6.4

)

• 

Remove the log set (if installed - see 

Section 16.0

)

Step 4:

 Place the other side panel along the remaining side of the 

firebox.

Figure 15.1.04:

Step 1:

 Place the rear panel in the back of the firebox.

Step 2:

 Place the left or right side panel along the corresponding 

side of the firebox. The side panels will hold the rear panel in 

place.

Figure 15.1.01:

Figure 15.1.02:

Figure 15.1.03:

Step 3:

 Install one of the upper panel clips in the top of the firebox 

to hold the top of the side panel in place.

Содержание 45-DVFE28LN-1





































































Отзывы:

Нет отзывов