manualshive.com logo in svg

Archgard 45-DVFE28LN-1, Инструкция по установке, эксплуатации и обслуживанию, Страница: 30 / 68

Поделиться
Скачать
Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 30

30

Installation

15.1  Brick Panel Installation

15.0  Firebox Liner Installation

The following steps highlight the procedure for installing brick panel firebox liners. Handle the panels with care as they are delicate. 

Inspect the panels to ensure that no damage has occurred inside the package. Please report any damage immediately to your 

Authorized Archgard Dealer.

Before you begin:

•  Ensure the gas supply is turned OFF and disconnect the power supply (including backup batteries)

• 

Open the Glass Door with Barrier Screen attached (see 

Section 6.4

)

• 

Remove the log set (if installed - see 

Section 16.0

)

Step 4:

 Slip the lower brick clips over the screws that were 

loosened in 

Step 2

. 

Figure 15.1.04:

Step 1:

 Lift the secondary air channels from the burner.

Step 2:

 Loosen the (2) screws securing the burner surround at the 

back of the firebox.

Figure 15.1.01:

Figure 15.1.02:

Figure 15.1.03:

Step 3:

 The lower brick clips are located in the manual bag with 

the fireplace.

Содержание 45-DVFE28LN-1





































































Отзывы:

Нет отзывов