manualshive.com logo in svg

Archgard 45-DVFE28LN-1, Инструкция по установке, эксплуатации и обслуживанию, Страница: 3 / 68

Поделиться
Скачать
Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 3

3

General Information

1.0  Introduction

Thank You and Congratulations for choosing an Archgard Gas Fireplace!

The 

45-DVFE28LN-1

 is one of the most advanced Direct Vent heaters available today. It is solidly designed using the latest technology 

and manufactured to the highest quality. It is our aim to provide you with an appliance that brings many trouble-free years of reliable 

service.

Some of the many features of your 

45-DVFE28LN-1

 are:

• 

Heater Classification

This fireplace is classified as a heating appliance. Therefore, it uses Direct Vent safety technology and it 

is suitable for continuously operated zone heating.

• 

High Efficiency

This fireplace has one of the highest efficiencies of any Direct Vent gas fireplace heaters, ensuring it is 

less expensive to operate.

• 

Adjustable Fan Speed This fireplace comes complete with an adjustable six speed circulation fan controlled with the remote.

• 

Adjustable Flame

This fireplace provides the ability to adjust the flame aesthetics and heat output to suit the owner's liking 

and heating needs.

• 

Solid Construction

This fireplace is mainly constructed of 16 and 18 gauge galvanized and aluminized coated steel for long 

life and durability.

• 

Optional Accessories

Speak with your local Authorized Archgard Dealer for a full complement of decorative accessories to suit 

your home's decor and personal tastes.

• 

Electronic Control 

System

This fireplace comes standard with the Dynamic Start Advantage. This new electronic ignition system 

is the latest in fireplace technology. It helps to create a better draft, better flame appearance, less 

condensation on the glass, and years of carefree operation. See 

Section 17.4

 for complete explanation 

of how the system works.

• 

Multiple Electronic 

Pilot Settings

This fireplace uses a gas control valve that is operated by a Multifunction Remote Control. It can be 

set up as either an Intermittent Pilot Ignition (IPI) system, or Continuous Pilot on Demand Ignition (CPI) 

system (also known as a Pilot on Demand (POD)).

CPI vs IPI:

Continuous Pilot on Demand Ignition (CPI)

: In this mode the pilot runs continuously even when the main burner is off. The 

Continuous Pilot on Demand Ignition operates on a seven day cycle. If the main burner is not turned on for seven continuous days, the 

pilot will turn itself off. When the main burner is lit again the cycle repeats. The pilot will remain lit for seven days, even after the main 

burner is turned off. If the main burner is lit during a seven day timing cycle, the seven day timer will reset.

Intermittent Pilot Ignition (IPI)

: A fuel saving mode in which the pilot is only used when the main burner is on.

This appliance is shipped in IPI mode. IPI mode is often the preferred method, however, there are some situations where it may be 

preferable to switch the fireplace into CPI mode. For example, in colder climates the glass door or the front of the fireplace could 

become very cold to the touch. Dynamic Start Advantage will solve most problems experienced by older IPI operated fireplaces.

Please complete and submit the warranty registration card included in the back of this manual or by visiting us at: 

www.archgard.com/warranty-registration

Содержание 45-DVFE28LN-1





































































Отзывы:

Нет отзывов