manualshive.com logo in svg

Archgard 45-DVFE28LN-1, Инструкция по установке, эксплуатации и обслуживанию, Страница: 28 / 68

Поделиться
Скачать
Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 28

28

Installation

14.0  Conversion Kit Instructions

IMPORTANT: 

This fireplace is Natural gas ready.  If converting to LP gas, follow instructions below.

WARNING:

 This conversion kit shall be installed by a qualified service agency in accordance with the manufacturers instructions 

and all applicable codes and requirements of the authority having jurisdiction.  If the information in these instructions is not followed 

exactly, a fire, explosion or productions of carbon monoxide may result, causing property damage, personal injury or loss of life.  The 

qualified service agency is responsible for proper installation of this kit.  The installation is not proper and complete until operation of 

the converted appliance is checked as specified in the instructions supplied with the kit.  Refer to appliance owner’s manual or product 

data plate for proper inlet and manifold pressure adjustments and orifice sizing.

IMPORTANT:

 For high altitude installations above 4500 ft (1372 meters), consult local gas distributor or the authority having 

jurisdiction for proper derating methods.

KIT NUMBERS:  45-CKELP for LP gas and 45-CKENG for Natural Gas

KIT INCLUDES: 

• 

Gas conversion label (303-0128) 

• 

Burner orifice (part number 301-0068-52, #52 DMS for LPG) (part number 301-0068-38, #38 DMS for NG)

• 

Instruction Sheet 

• 

SIT 885 Valve conversion kit c/w instructions & gas type label

WARNING:  SHUT OFF GAS SUPPLY AND ELECTRICAL POWER TO FIREPLACE

 

        SHUT OFF GAS SUPPLY BEFORE DISCONNECTING ELECTRICAL POWER

14.1  Prepare the Fireplace

• 

Open the Glass door (see 

Section 6.3

), Brick Panel Set (if applicable, see 

Section 15

), and Logset (see 

Section 16

)

• 

Remove the Burner Surround (see 

Section 18.11

)

• 

Remove the Burner (see 

Section 18.12

)

Remove the burner orifice using a 1/2” wrench.  Replace with the orifice 

supplied with the conversion kit.  Use a small amount of pipe sealant on 

the threads of the orifice mount. Do not use too much as it can block the 

orifice.

14.2  Pilot Conversion

Using a 7/16” wrench and loosen the pilot hood 1/4 turn.  

Slide the tab at the bottom of the orifice hood all the way 

so the red side (propane) with the hole in it is showing.  

Tighten the pilot hood back up so that it is lined up with 

the two probes on both sides of the pilot assembly.

Figure 14.1.01:

Figure 14.2.01:

Содержание 45-DVFE28LN-1





































































Отзывы:

Нет отзывов