Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 68

Archgard 45-DVFE28LN-1 Скачать руководство пользователя страница 14

14

Installation

NOTE

This product must be installed by a qualified installer. The installer should follow the procedure best suited for each specific

installation.

1.

Prepare the fireplace location, allowing for vent installation and type of installation (corner or flat wall application).

2.

Install hearth (if applicable).

3.

Complete electrical hook-up.

4.

Complete gas line installation.

5.

Complete venting installation.

6.

Verify all clearances.

7.

Install the panel set. Many options are available from your local Archgard dealer.

8.

Install the logs, glass door assembly, and barrier screen.

9.

Verify proper operation of fireplace and all components.

PLACEMENT CLEARANCE REQUIREMENTS

•

This fireplace must be installed on a level surface capable of supporting the fireplace and venting

•

Due to high surface temperatures, fireplace should be located out of traffic and away from furniture and draperies

•

This fireplace may be installed in a bedroom (see local codes)

•

Please be aware of the large amount of heat this fireplace will produce when determining a location

9.1 Installation Overview

9.0 Prepare The Fireplace

«
...
12
13
14
15
16
...
»

Содержание 45-DVFE28LN-1





































































Отзывы:

Нет отзывов