27
Installation
11.2 Typical Corner Installation
C: 44.40"
D: 45.25"
B: 50. 5"
A: 1.0"
E: .1"
0.50"
D: 45.25"
F: 35.5"
G: 4.0"
A: 1.0"
D: 45.25"
H: 1
.33"
0.25"
0.25"
5.50"
3.50"
A
A
B
B
4
4
3
3
2
2
1
1
DO NOT SCALE DRAWING
41-DVT C rn r In a
SHEET 1 OF 2
n
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:50 WEIGHT:
REV
DWG. NO.
SIZE
TITLE:
NAME
DATE
COMMENTS:
.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
FINISH
MATERIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
APPLICATION
USED ON
NE T ASS
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERT OF
INSERT COMPAN NAME HERE . AN
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
INSERT COMPAN NAME HERE IS
PROHIBITED.
C: 44.40"
D: 45.25"
B: 50. 5"
A: 1.0"
E: .1"
0.50"
D: 45.25"
F: 35.5"
G: 4.0"
A: 1.0"
D: 45.25"
H: 1
.33"
0.25"
0.25"
5.50"
3.50"
A
A
B
B
4
4
3
3
2
2
1
1
DO NOT SCALE DRAWING
41-DVT C rn r In a
SHEET 1 OF 2
n
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:50 WEIGHT:
REV
DWG. NO.
SIZE
TITLE:
NAME
DATE
COMMENTS:
.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
FINISH
MATERIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
APPLICATION
USED ON
NE T ASS
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERT OF
INSERT COMPAN NAME HERE . AN
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
INSERT COMPAN NAME HERE IS
PROHIBITED.
Dimension
3/8" Wall Board
1/2" Wall Board
5/8" Wall Board
3/4" Wall Board
A
71.25"
71"
70.75"
70.50"
B
50.75"
50.75"
50.75"
50.75"
C
44.40"
44.40"
44.40"
44.40"
D
45.42"
45.25"
45.07"
44.89"
E
67.81"
67.81"
67.81"
67.81"
F
32.12"
35.50"
31.87"
31.74"
G
64.24"
64"
63.75"
63.50"
H
17.33"
17.33"
17.33"
17.33"
Dimensions shown in
Figure 11.2.01
are when using 1/2" wall board. If using a facing material that is an alternative thickness, refer to
the table below for appropriate dimensions.
Refer to
Section 11.1
and
Section 9.2
for information on nailing flange settings and installation.
Figure 11.2.01
IMPORTANT
If installing IHEAT, see the IHEAT manual for framing dimensions and specifications.