manualshive.com logo in svg

Archgard 36- D VI E40LN - 1, Инструкция по установке, эксплуатации и обслуживанию, Страница: 49 / 76

Поделиться
Скачать
Archgard 36- D VI E40LN - 1 Скачать руководство пользователя страница 49

49

Operation

Initializing the System for Handheld / Wall Mount Remote Operation

1.

Connect IFC Control Module to AC power supply. A single “beep” will indicate the presence of power. 

NOTE: Th i s  w i l l  i n i t i a t e  Pi l o t  

St a r t -u p  i n  Ma n u a l  Mo d e .  Th e  p i l o t  w i l l  s p a r k  r e p e a t e d l y  a n d  i g n i t e  i f  g a s  h a s  b e e n  s u p p l i e d  t o  t h e  u n i t

. 

Sy n c  t h e  c o n t r o l  

board to the remote to turn main burner and pilot o  using the steps below.

2.

The ON/OFF Override Jumper on the control board must be connected.

3.

Press and hold th red SW1 button until the IFC module beeps three (3) times and/or the amber LED illuminates indicating the 

module is ready to synchronize with the remote.

4.

Within ten (10) seconds push the ON/OFF key on the remote. The IFC module will “beep” four (4) times to indicate that it has 

successfully synced with the remote. Turn the fireplace OFF using the ON/OFF button on the remote to complete initialization. The 

remote will now control the fireplace.

5.

Install the provided four (4) AA batteries into battery back up holder.

Tu r n  " ON"  t h e  Ap p l i a n c e

With the system OFF, press the ON/OFF Key on the 

Remote. The Remote display will show other active 

icons on the screen. At the same time the Receiver 

will activate the appliance. A single “beep” from the 

receiver will confirm reception of the command.

Tu r n  " OFF"  t h e  Ap p l i a n c e

With the system ON, press the ON/OFF Key on the 

Remote. The Remote display will show the current 

room temperature. At the same time the Receiver 

will turn the appliance off. A single “beep” from the 

receiver will confirm reception of the command.

Fi g u r e  19 . 5. 04:

Fi g u r e  19 . 5. 05:

Ba t t e r y  C o m p a r t m e n t

Proflame II IFC Module

Содержание 36- D VI E40LN - 1













































































Отзывы:

Нет отзывов