27-DVIM22
29
LIGHTING INSTRUCTIONS ON RATING PLATE
303-0001
A. This appliance has a pilot which must be lighted by a spark ignitor.
When lighting the pilot follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be
sure to smell next to the floor because some gas is heavier than air
and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any phone in your
building.
•
Immediately call your gas supplier from a neighbor’s phone. Follow
the gas supplier’s instructions.
•
If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never
use tools. If the knob will not push in or turn by hand don
’
t try to
repair it, call a qualified service technician. Forced or attempted
repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and any gas
control which has been under water.
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING:
If you do not follow these instructions exactly, a fire of explosion may result causing property damage,
personal injury or loss of life.
1. STOP! Read the safety information above on this label.
2. Set the remote switch to “
OFF
”.
Set the thermostat to the lowest
setting. (Only if your appliance is equipped with these devices.)
3. Turn off all electric power to the appliance.
4. Open lower louvers or access door.
3. Press slightly and turn the control knob clockwise
to the “
OFF
”
position.
4. Wait 5 minutes to clear out any gas. Then smell for gas, including near
the floor. If you smell gas, STOP! and follow instruction “
B
”
above.
5. Find pilot. It is located between the logs near the center behind the
burner.
6. Press slightly and turn control knob counterclockwise
to “
PILOT
”.
Depress knob and light pilot by repeatedly pressing the sparker. Once
flame is established, hold knob depressed for approximately 30
seconds. Release knob. If pilot should go out, repeat steps 3 to 5.
•
If the knob does not pop up when released, stop and immediately call
your service technician or gas supplier.
•
If the pilot will not stay lit after serveral tries, turn the gas control knob
to “
OFF
”
and call your service technician or gas supplier.
7. Turn gas control knob counterclockwise
to “
ON
”
and set the flame
adjustment knob to the desired heat setting from “
LO
”
to “
HI
”.
8. Set the remote switch to “
ON
”.
Set the thermostat to the desired setting.
(Only if your appliance is equipped with these devices.)
9. Turn on all electric power to the appliance.
10. Close louver or access door.
LIGHTING INSTRUCTIONS
TO TURN OFF GAS TO APPLIANCE
1. Set the thermostat to the lowest setting and turn the remote switch to
“
OFF
”.
2. Turn off all electric power to the appliance if service is to be performed.
3. Open lower louvers or access door.
4. Press slightly and turn control knob clockwise
to “
OFF
”.
Do not force.
5. Close lower louvers or access door.
A. This appliance has a pilot which must be lighted by a spark ignitor.
When lighting the pilot follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be
sure to smell next to the floor because some gas is heavier than air and
will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any phone in your
building.
•
Immediately call your gas supplier from a neighbor’s phone. Follow the
gas supplier’s instructions.
•
If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never use
tools. If the knob will not push in or turn by hand don
’
t try to repair it,
call a qualified service technician. Forced or attempted repair may
result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the appliance
and to replace any part of the control system and any gas control which
has been under water.
Flame Adjustment
Knob
Control Knob
OUT
(manifold)
IN (inlet)
Pilot
Fig. 29-A
Fig. 29-B