background image

ARC AUDIO WARRANTY AND

SERVICE GUIDELINES

 

ARC AUDIO warrants all new KAR Series Amplifiers against defects in 

material and workmanship for a period of 

ONE (1) YEAR

 from the original date of 

purchase.  This warranty is not transferable and applies only to the 

original retail 

purchaser

 of the product from an authorized ARC AUDIO retailer. Upon inspection by 

ARC AUDIO should services be necessary under this warranty for any reason due to 
manufacture defects ARC AUDIO will, at its sole discretion, repair or replace the 
defective product with new or similar conditioned product at no charge.

High Performance Audio Amplifier

CLASS H

 

MONO BLOCK

KS 1200.1

KS 1200.1

THIS WARRANTY DOES NOT COVER INSTALLATION OR DAMAGE 
RESULTING FROM ACCIDENT, MISUSE, ABUSE, IMPROPER WIRING, 
OPERATION OUTSIDE OF UNIT OUTSIDE OF MANUFACTURES SPECIFICA-
TIONS, OR AGAINST INSTRUCTIONS IN OWNERS MANUAL. IN ADDITION 
ANY PRODUCT THAT HAS BEN OPENED, TEMPERED WITH OR MODIFIED, 
OR IF ANY SERIAL NUMBERS HAVE BEEN REMOVED WILL NOT BE 
COVERED BY ANY PART OF THE MANUFACTURES WARRANTY.

All warranty returns should be sent to ARC AUDIO freight prepaid and must be accompa-
nied by proof of purchase (a copy of the original sales receipt). Direct returns from 
consumers or non-authorized retailers will be refused unless specifically authorized by 
ARC AUDIO with a valid return authorization number. To receive a Return Authorization 
number call ARC Audio Warranty Department. Be prepared to give you name, address, 
phone number, model number and serial number of the defective unit.. 

All warranty returns should be packed in original packaging and must be accompa-
nied by a copy of the original sales receipt. Product damaged in shipment will not be 
covered under this warranty. The customer or retailer may choose to have this 
damage repaired at the normal “Out of Warranty” repair cost.

In no event will ARC AUDIO be liable for incidental, consequential, or other damages 
resulting from the use of this product, this includes but is not limited to, damage of 
hearing, property or person, damage based upon inconvenience or on loss of use of the 
product, and to the extent permitted by law, damages for personal injury. This warranty 
gives you specific legal rights, and you may have other rights, which vary from state to 
state. This warranty applies to products sold and used in the United States of America. In 
all other countries please contact your distributor.

REV.

 2011-9-26-M.Z.

For warranty and non-warranty repairs, send to:

ARC Audio
4719 Greenleaf Cr. #4
Modesto CA, 95356

KS 2500.1

KS 2500.1

Содержание KS 1200.1









Отзывы: