Aradex VECTOPOWER VP5000-DC Скачать руководство пользователя страница 45

Страница: 45 / 173

VP5000-DC/DC60, VP5000-DC/DC200-HL

Product description

Last edited 2019-02-08
by Sonja Scheunert

Filename
VP5000_DCDC60_200-HL_installation_manual_v1-4en.docx

45 / 173

3.7.1

[ST1] design and pin assignment

Figure 20: Pin assignment [ST1]

The pin assignment on the device connector is
shown.

Design

Manufacturer: AMP
Connector type: AMPSEAL HDR SNAP IN W/G 23-
pin
Connector design: Housing variant WF

Please note that the VECTOPOWER is delivered
without mating connectors. See chapter 3.13
Product description, Accessories that can be
obtained from ARADEX AG and chapter 3.14 Product
description, Accessories that the customer must
provide.

Function

This connection is the standard connection of the
VECTOPOWER motherboard.

Application

The following pins must be connected for the power
supply:
- Pin 1 KL_31 / GND
- Pin 2 KL_30B / 24V

The following pin must be connected for a hardware
enable :
- Pin 3 Enable

The pins for the CAN bus and the RS-232 interface
are available at [ST1] for communication and
software enable.

Pin no.

Description

Function

KL_31 / GND

Ground; is also the ground for pins 3, 4, 5, 13, 16, 17.

KL_30B / 24

Supply 24

V DC

Enable

Enable signal for VECTOPOWER

Digi_Out1

Digital output 1 Open collector type

Digi_Out2

Digital output 2 Open collector type

NTC1

NTC temperature sensor 1

NTC2

NTC temperature sensor 2

AN_I1+

Analog current input 1 positive pin

CAN_L

CAN bus low

Содержание VECTOPOWER VP5000-DC














































































































































































Результаты поиска

Содержание VECTOPOWER VP5000-DC

Отзывы:

Похожие инструкции для VECTOPOWER VP5000-DC

Бренды по названию

Популярные бренды

Aradex VECTOPOWER VP5000-DC, Руководство по установке

Результаты поиска

Содержание VECTOPOWER VP5000-DC

Отзывы:

Похожие инструкции для VECTOPOWER VP5000-DC

Бренды по названию

Популярные бренды