AR 10052412, Руководство по эксплуатации и обслуживанию

Страница: 47 / 80

Model 5000A225C
Rev A 23
A#
Control
Line
Fault Details RF
Inhibit?

= Yes
Drop to
RF OFF?

= Yes Hex Dec
Fault Text
(<15 Characters)
Description
A60 J5-30 0x020f 527 Amp A27 Amplifier Fault, Module A27

A60 J5-31 0x0210 528 Amp A28 Amplifier Fault, Module A28

A60 J5-32 0x0211 529 Amp A29 Amplifier Fault, Module A29

A61 J5-15 0x0400 1024 Therm A1 Thermal Fault, Module A1
 
A61
J5-16
0x0401 1025 Therm A2 Thermal Fault, Module A2
 
A61 J5-17 0x0402 1026 Therm A14 Thermal Fault, Module A14
 
A61 J5-18 0x0403 1027 Therm A15 Thermal Fault, Module A15
 
A61 J5-19 0x0404 1028 Therm A16 Thermal Fault, Module A16
 
A61 J5-20 0x0405 1029 Therm A17 Thermal Fault, Module A17
 
A61 J5-21 0x0406 1030 Therm A18 Thermal Fault, Module A18
 
A61
J5-22
0x0407 1031 Therm A19 Thermal Fault, Module A19
 
A61 J5-23 0x0408 1032 Therm A20 Thermal Fault, Module A20
 
A61 J5-24 0x0409 1033 Therm A21 Thermal Fault, Module A21
 
A61 J5-25 0x040a 1034 Therm A22 Thermal Fault, Module A22
 
A61
J5-26
0x040b 1035 Therm A23 Thermal Fault, Module A23
 
A61 J5-27 0x040c 1036 Therm A24 Thermal Fault, Module A24
 
A61
J5-28
0x040d 1037 Therm A25 Thermal Fault, Module A25
 
A61 J5-29 0x040e 1038 Therm A26 Thermal Fault, Module A26
 
A61 J5-30 0x040f 1039 Therm A27 Thermal Fault, Module A27
 
A61 J5-31 0x0410 1040 Therm A28 Thermal Fault, Module A28
 
A61
J5-32
0x0411 1041 Therm A29 Thermal Fault, Module A29
 
2.8 REMOTE OPERATION
This section describes remote operation of the amplifier using the provided General Purpose Interface Bus
(GPIB), RS-232 serial port, fiber-optic serial ports, Universal Serial Bus (USB), and Ethernet port. All ports
are always active, however only one port may be used at a time.
NOTE : Communicating through two or more ports at one time will cause data collisions and lost commands
or queries.
The Keylock switch on the control panel of the amplifier enables the remote-control functionality and must be
set to the REMOTE position before any commands will be accepted. All remote queries will work with the
Keylock switch in any position. When the Keylock switch is set to REMOTE, all front panel controls are
disabled unless otherwise specified.
The status of the amplifier should be checked remotely just prior to issuing a command as well as after a
command has been issued to ensure the command has been properly executed. When checking the status after
issuing a command, it is good practice to add a delay of 100ms or more to allow the control system time to
process the command.