manualshive.com logo in svg
background image

AUTOMATIC POOL CLEANER

O   W   N   E   R ’   S

M   A   N   U   A   L

OPERATION, TROUBLESHOOTING & PARTS

AquaTools

293 Wright Street, Delavan, WI 53115

International:

262-728-5551, FAX: 262-728-7550

© 2003, AquaTools

Printed in U.S.A.

AT364 

(Rev. 5/7/03)

ABOUT SAFETY

• Before installing the cleaner, review and 

understand all warnings and safety information
on inside cover of manual.

ABOUT INSTALLATION

• Please use the convenient, water resistant

Installation Instructions

card.

INDEX

About Safety .............................................................2
About Your Pool and Filter System ...........................2
About Installation .....................................................3
About the Cleaner Operation....................................4
About ”Fine Tuning” Vacuum Adjustments............4,5
About the Cleaner and Accessories...........................6
About Troubleshooting .............................................7
About Disassembly ...................................................8
About Assembly........................................................9
Repair Parts.............................................................10
About Maintenance ................................................11
Warranty.................................................................12

1873 0795

Model AT5800

Содержание AT5800













Отзывы: