Aquacal TropiCool TC1000 Скачать руководство пользователя страница 13

Страница: 13 / 35

Page - 10

The maximum static pressure (or operating pressure) is 50 pounds-per-square-inch (PSI). These specifications
relate to the chiller only.

Code-specified whole system turnover rates must be satisfied.

1.4.f Maintaining Ability to Winterize

Do not glue the threaded portion of the unions. The unions are used to decouple the chiller from the plumbing
system during hard freeze conditions.

NOTICE

Failure to heed the following may result in damage to equipment.

Do not use glue on the threaded portion of the equipment’s unions. A glued-in-place union will prevent the chiller
from being properly winterized.

1.4.g Adjusting Water Pressure Switch

Adjust water pressure switch when chiller attempts to operate without water flow.

Before attempting any adjustments confirm the following :

The filter is clean.

Filter pump is operating.

The valves are set to direct the appropriate amount of water through the
chiller.

See "Water Flow Rates" on page 9.

FLO

is displayed (or displays intermittently).

WARNING

Failure to heed the following may result in injury or death.

Water Pressure Switch adjustment procedure to be performed by experienced service personnel only; procedure
must not be attempted by individuals lacking adequate electrical and mechanical experience.

NOTICE

Failure to heed the following may result in damage to equipment.

If the chiller continues to operate after a water pressure switch adjustment, deactivate equipment and perform
additional troubleshooting.

Содержание TropiCool TC1000




































Результаты поиска

Содержание TropiCool TC1000

Отзывы:

Похожие инструкции для TropiCool TC1000

Бренды по названию

Популярные бренды

Aquacal TropiCool TC1000, Руководство по установке

Результаты поиска

Содержание TropiCool TC1000

Отзывы:

Похожие инструкции для TropiCool TC1000

Бренды по названию

Популярные бренды