APS CFS108 Скачать руководство пользователя страница 60

Страница: 60 / 146

CFS100 SERIES OPERATION MANUAL

SECTION 6: FRONT PANEL OPERATION

Entire Contents Copyright



APS CFS100 Series Power Source Operation Manual

Page 60 of 146

6.5

Setup Screen Readouts

The setup screen is identified by the word “Set” in the upper left corner of the LCD. The

table below shows the various readouts that are found in the setup screen and their

meaning.

On Screen Fields

Description

M1-1

Indicates the power source is in PROGRAM mode. Possible

indicators are:

Mn-m PROGRAM Mode, Memory <n>, Step <m>

MANUAL Mode, Memory <n>

Mn DC DC Mode, Memory <n>

For details on available operating modes, refer to Section 6.8

through 6.17.

10.0s

Instrument Timer for Output

F: 60.0Hz

Frequency measurement value display

Set

State of power source. Available states are:

Set

Setup mode

Dwell Output applied, executing dwell time

Pass Test completed, result = Pass

Abort Test aborted by Operator

Fault Test aborted due to Fault condition

P: 0.0W

Power measurement value

Ap: 0.000A

Peak Current measurement value

PF:0.000

Power Factor measurement value

150.0v

Left hand, Large Font Voltage set value or measurement. Set

value in set screens, measurement value when output is ON.

0.011

Right hand, large Font measurement value. Can be any of the

other available measurements. Default is Current (A).

Table 6-2: Setup (Set) Screen Display Fields Description

Содержание CFS108



















































































































































Результаты поиска

Содержание CFS108

Отзывы:

Бренды по названию

Популярные бренды

APS CFS108, Руководство по эксплуатации

Результаты поиска

Содержание CFS108

Отзывы:

Бренды по названию

Популярные бренды