APS CFS108 Скачать руководство пользователя

Страница: 143 / 146

CFS100 SERIES OPERATION MANUAL

SECTION 11: CE MARK DECLARATION

Entire Contents Copyright



APS CFS100 Series Power Source Operation Manual

Page 143 of 146 PN 160951-10

CE MARK Declaration of Conformity

EU Directives:

2006/95/EC and 93/68/EEC

Manufacturer

Adaptive Power Systems, Inc.

Product Name

CFS100 Series AC & DC Power Sources

Serial Number

___________

The manufacturer hereby declares that the products are in conformity with the following standards or

other normative documents:

RoHS (DIRECTIVE 2011/65/EU)

Standard applied EN 50581:2012 (Exempt as WEEE Category 9 until 22 July 2017)

SAFETY (DIRECTIVE 2006/95/EC):

Standard applied EN 61010–1: 2010 (3rd Edition)

EMC (DIRECTIVE 2014/30/EU):

Standard applied EN 61326-1: 2013

EMC (DIRECTIVE 2014/30/EU):

Standard applied EN 61326-1: 2013

ELECTROMAGNETIC EMISSIONS:

Radiated Emissions CISPR 11/22, CLASS A LIMITS

Conducted Emissions CISPR 11/22, CLASS A LIMITS

ELECTROMAGNETIC IMMUNITY:

RF Electromagnetic Field

IEC 61000-4-3:2006+A1:2007+A2:2010

1 kHz sinewave (80% AM)

80 – 1000 MHz, 10 V/m

1.4 – 2 GHz, 3 V/m

2.0 – 2.7 GHz, 1 V/m

Conducted RF Immunity

IEC 61000-4-6:2013

Conducted RF Immunity 0.15-80 MHz @ 3 Vrms

Electrostatic Discharge

IEC 61000-4-2:2008

±4 kV contact discharge

±8 kV air discharge

Electrical Fast Transient/Burst

IEC 61000-4-4:2004+A1:2010

AC or DC power ports, ±2 kV

Signal and I/O ports, ±1.0 kV

Surge

IEC 61000-4-5:2005

AC or DC power ports, ±2 kV Line to ground and ±1.0 kV line to line

Power Frequency Magnetic Field IEC 61000-4-8:2009

30 A/M

Supplemental Information:

When and Where Issued:

June 4, 2016

Irvine, California, USA

Authorized Signatory

Quality Assurance Inspector

Adaptive Power Systems

Responsible Person

Production Manager

Adaptive Power Systems

17711 Fitch

Irvine, California, 92649, USA

Mark of Compliance, LVD

Содержание CFS108



















































































































































Результаты поиска

Содержание CFS108

Отзывы:

Похожие инструкции для CFS108

Бренды по названию

Популярные бренды

APS CFS108, Руководство по эксплуатации

Результаты поиска

Содержание CFS108

Отзывы:

Похожие инструкции для CFS108

Бренды по названию

Популярные бренды