APS 42L Series Скачать руководство пользователя

Страница: 11 / 88

SECTION 2: FRONT MATTER

Entire Contents Copyright



42L Series Modular DC Load Operation Manual

Page 11 of 88

2.4

Safety Notices

SAFETY SUMMARY

The following general safety precautions must be observed during all phases of operation,

service, and repair of this instrument. Failure to comply with these precautions or with

specific warnings elsewhere in this manual violates safety standards of design, manufacture,

and intended use of the instrument. Adaptive Power Systems assumes no liability for the

customer's failure to comply with these requirements.

GENERAL

This product is a Safety Class 1 instrument (provided with a protective earth terminal). The

protective features of this product may be impaired if it is used in a manner not specified in

the operation instructions.

ENVIRONMENTAL CONDITIONS

This instrument is intended for indoor use in an installation category I, pollution degree 2

environments. It is designed to operate at a maximum relative humidity of 80% and at

altitudes of up to 2000 meters. Refer to the specifications tables for the ac mains voltage

requirements and ambient operating temperature range.

BEFORE APPLYING POWER

Verify that the product is set to match the available line voltage and the correct fuse is

installed.

GROUND THE INSTRUMENT

This product is a Safety Class 1 instrument (provided with a protective earth terminal). To

minimize shock hazard, the instrument chassis and cabinet must be connected to an

electrical ground. The instrument must be connected to the AC power supply mains through

a properly rated three-conductor power cable, with the third wire firmly connected to an

electrical ground (safety ground) at the power outlet. Any interruption of the protective

(grounding) conductor or disconnection of the protective earth terminal will cause a

potential shock hazard that could result in personal injury.

FUSES

Only fuses with the required rated current, voltage, and specified type (normal blow, time

delay, etc.) should be used. Do not use repaired Fuses or short circuit the fuse holder. To do

so could cause a shock or fire hazard.

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE.

Do not operate the instrument in the presence of flammable gases or fumes.

Содержание 42L Series

























































































Результаты поиска

Содержание 42L Series

Отзывы:

Похожие инструкции для 42L Series

Бренды по названию

Популярные бренды

APS 42L Series, Руководство по эксплуатации

Результаты поиска

Содержание 42L Series

Отзывы:

Похожие инструкции для 42L Series

Бренды по названию

Популярные бренды