Applied Biosystems GeneAmp PCR System 9700 Скачать руководство пользователя страница 119

Страница: 119 / 132

Contacting Technical Support C-3

To Contact Technical

Support by

Telephone or Fax

(North America)

To contact Applied Biosystems Technical Support in North America, use the telephone
or fax numbers in the table below.

Note

To schedule a service call for other support needs, or in case of an emergency, dial

1.800.831.6844, then press 1.

Product/Product Area

Telephone

Fax

ABI P

RISM

3700 DNA Analyzer

1.800.831.6844,
then press 8

1.650.638.5981

DNA Synthesis

1.800.831.6844,
press 2, then press 1

1.650.638.5981

Fluorescent DNA Sequencing

1.800.831.6844,
press 2, then press 2

1.650.638.5981

Fluorescent Fragment Analysis
(including GeneScan

applications)

1.800.831.6844,
press 2, then press 3

1.650.638.5981

Integrated Thermal Cyclers (ABI P

RISM

877 and Catalyst 800 instruments)

1.800.831.6844,
press 2, then press 4

1.650.638.5981

ABI P

RISM

3100 Genetic Analyzer

1.800.831.6844,
press 2, then press 6

1.650.638.5981

Peptide Synthesis
(433 and 43x Systems)

1.800.831.6844,
press 3, then press 1

1.650.638.5981

Protein Sequencing
(Procise

Protein Sequencing Systems)

1.800.831.6844,
press 3, then press 2

1.650.638.5981

Sequence Detection Systems
(Real-Time PCR) and PCR

1.800.762.4001,
then press:

1 for PCR

2 for TaqMan

applications and
Sequence Detection
Systems including ABI
Prism

‚

7700, 7900,

and 5700

6 for the 6700
Automated Sample
Prep System

1.800.831.6844, then
press 5

1.240.453.4613

♦

Mariner

ESI-TOF Mass

Spectrometry Workstations

♦

Voyager

MALDI-TOF

Biospectrometry Workstations

♦

MassGenotyping Solution 1

(MGS1)

Systems

♦

Proteomics Solution 1

(PS1)

Systems

♦

ICAT

Reagent

1.800.899.5858,
press 1, then press 3

1.508.383.7855

Содержание GeneAmp PCR System 9700





































































































































Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems GeneAmp PCR System 9700, Руководство пользователя

Результаты поиска

Содержание GeneAmp PCR System 9700

Отзывы:

Бренды по названию

Популярные бренды