manualshive.com logo in svg

Applied Biosystems 7300, Руководство по установке и обслуживанию

Поделиться
Скачать
Applied Biosystems 7300 Скачать руководство пользователя страница 47

Chapter 2

Unpacking and Setting Up the Instrument

Setting Up the 7300/7500/7500 Fast Instrument

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

21

Notes

2

4.

Close the access door of the instrument.

5.

Connect the power cord to the 7300/7500/7500 
Fast instrument, then to the receptacle wall 
circuit.

Note:

Power cords for different voltages are 

provided in the packing kit. Connect the cord 

with the receptacle appropriate for your voltage, 

then discard remaining cables.

6.

Press the power button at the lower right front 
panel, then wait for the 7300/7500/7500 Fast 
system to boot (about 30 seconds).

7.

When the Power status light on the lower left 
front panel lights, press the tray to open it.

8.

Remove the packaging plate from the tray and 
set it aside.

Note:

Do not discard the packaging plate. Use it 

for long-term shutdown of the system (see 

page 104

).

Remove

Содержание 7300















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды