Applied Biosystems 2720 Скачать руководство пользователя страница 54

Страница: 54 / 151

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 4

Temperature non-uniformity test

Evaluating the

results

After the GeneAmp

9700 completes the temperature non-uniformity test, the TNU

Performance screen opens. See the table below to evaluate the results.

Ending the test

1. Press

(Cancel).

2. Remove the 0.2-mL probe assembly from the sample block.

3. Power off the digital thermometer, then clean off the oil.

4. Wait for the sample block to reach room temperature (~25 °C), then remove the

dual 96-well temperature verification plates from the sample block.

PHYSICAL INJURY HAZARD.

Hot Surface. Use care

when working around the heated cover and sample block to avoid being burned
by hot components.

5. Clean the oil off the sample block.

If the...

Then...

Temperature of the
sample block wells is
uniform

“Pass” appears after each setpoint temperature.

Temperature variation of
the sample block wells
exceeds performance
specifications

“Fail” appears after the setpoint temperature(s) for which the
test failed.

• If the test fails, repeat the procedure to make sure that the

thermometer was not misread or that data-entry errors
were not made.

• If the test fails again, contact Applied Biosystems Technical

Support. See

“How to obtain support” on page viii

TNU Performance

TNU at 95°C is xx.xx - Pass
TNU at 55°C is xx.xx - Pass

Cancel

TNU Performance

TNU at 95°C is xx.xx - Fail
TNU at 55°C is xx.xx - Fail

Cancel

Содержание 2720
























































































































































Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems 2720, Руководство пользователя

Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды