Applied Biosystems 2720 Скачать руководство пользователя страница 146

Страница: 146 / 151

138

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Appendix D Safety

Instrumentation safety

Symbols on instruments

Electrical

symbols on

instruments

The following table describes the electrical symbols that may be displayed on
Applied Biosystems instruments.

Symbol

Description

Indicates the

position of the main power switch.

Indicates the

Off

position of the main power switch.

Indicates a standby switch by which the instrument is switched on to
the

Standby

condition. Hazardous voltage may be present if this

switch is on standby.

Indicates the

On/Off

position of a push-push main power switch.

Indicates a terminal that may be connected to the signal ground
reference of another instrument. This is not a protected ground
terminal.

Indicates a protective grounding terminal that must be connected to
earth ground before any other electrical connections are made to the
instrument.

Indicates a terminal that can receive or supply alternating current or
voltage.

Indicates a terminal that can receive or supply alternating or direct
current or voltage.

Содержание 2720
























































































































































Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems 2720, Руководство пользователя

Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды