Applied Biosystems 2720 Скачать руководство пользователя страница 137

Страница: 137 / 151

129

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Recalibration

This appendix describes how to order a recalibration service for your Temperature
Verification System.

Obtaining recalibration

Introduction

Applied Biosystems recommends that the Model 4500 digital thermometer and
Probe Assembly be recalibrated on an annual basis.

To have your thermometer and probe recalibrated:

1. Decontaminate the probe assembly (see below).

2. Send the equipment to the manufacturer (see below).

Decontaminating

the probe

assembly

Gently wipe the probe cone with a cotton swab that has been moistened with bleach
solution (20% bleach, 80% water).

IMPORTANT!

Do not submerge the probe in bleach solution. Do not disassemble the

probe assembly.

CHEMICAL HAZARD. Sodium hypochlorite (bleach)

is a

liquid disinfectant that can be corrosive to the skin and can cause skin
depigmentation. Read the MSDS, and follow the handling instructions. Wear
appropriate protective eyewear, clothing, and gloves.

Sending

equipment to

Alpha Technics

1. Inform Alpha Technics of the recalibration order by visiting the Alpha Technics

web site at

http://www.alphatechnicsonline.com

and following the online

instructions.

Ship the Temperature Verification kits to:

Alpha Technics

17151 Gillette Avenue

Irvine, CA. 92614-5602

2. Ensure that the probe assembly is decontaminated.

3. Pack the Model 4500 digital thermometer and probe assembly in the black case.

Содержание 2720
























































































































































Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems 2720, Руководство пользователя

Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды