Applied Biosystems 2720 Скачать руководство пользователя страница 121

Страница: 121 / 151

113

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 9

Temperature non-uniformity test

Calculating test

results

Use the following information to calculate the results of the test.

Note:

If there is more than one GeneAmp

9600 in your laboratory, verify that the

serial number on the calibration label matches the serial number on the instrument
that you are testing.

For the 16 Setpoint #1 measurements (95 °C hold), subtract the lowest measured
temperature from the highest measured temperature.

For the 16 Setpoint #2 measurements (40 °C hold), subtract the lowest measured
temperature from the highest measured temperature.

either

result is more than

1 °C from the setpoint, your GeneAmp

9600 must be

serviced by an Applied Biosystems service representative.

Ending the test

1. Remove the 0.2-mL probe assembly from the sample block.

2. Power off the digital thermometer, then clean off the oil.

3. Wait for the sample block to reach room temperature (~25 °C), then remove the

9600 temperature verification frame from the sample block.

PHYSICAL INJURY HAZARD.

Hot Surface. Use care

when working around the heated cover and sample block to avoid being burned
by hot components.

4. Clean the oil off the sample block.

Содержание 2720
























































































































































Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems 2720, Руководство пользователя

Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды