Applent Instruments Anbai AT4808 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 35

Applent Instruments Anbai AT4808 Скачать руководство пользователя страница 26

26

AT4808 User's Guide

8.

Remote Control

This chapter provides the following information to remotely control the FM8116R via the
RS-232C or USB interface.This chapter provides the following information



Select Baud Rate.



About SCPI

8.1

To Select Baud Rate

Before you can control the FM8116R by issuing RS-232 commands from built-in RS-232
controller connected via its DB-9 connector, you have to configure the RS-232 baud rate.

The FM8116R’s built-in RS-232 interface uses the SCPI language.

The configuration of RS-232

RS-232 configuration is as follows:

Data bits:

8-bit

Stop bits:

1-bit

Parity:

none

To set up the baud rate

Step 1.

Press the [Setup] key

Step 2.

Use the cursor key to select [BAUD] field

Step 3.

Use the soft keys to select baud rate.

Soft key

Function

9600

19200

38400

57600

115200

Recommend

8.2

SCPI Language

Standard Commands for Programmable Instruments (SCPI) is fully supported by the

NOTE:
FM8116R ONLY supports the SCPI Language.

«
...
24
25
26
27
28
...
»

Содержание Anbai AT4808




































Отзывы:

Нет отзывов