API A790 Скачать руководство пользователя страница 118

Страница: 118 / 138

Troubleshooting 8-10

Use the Web Manager/Telnet of the Access Point to check whether it
is connected to the network.

Reconfigure and reset the Access Point.

I cannot access the network.

Make sure that the necessary driver(s) is correctly installed.

Make sure that the network configuration is appropriate.

Make sure that the user name or password is correct.

You have moved out of range of the network.

Turn off power management.

Modem Problems

The modem does not work.

Make sure that the device driver is correctly installed.

Make sure that the telephone line is properly connected.

Make sure that the COM port in the communication software is
correctly set.

Turn off power management.

PC Card Problems

The PC card does not work.

Make sure that the PC card is correctly seated.

If the card requires an IRQ (Interrupt ReQuest), make sure that there
is one available.

The PC card stops communicating properly.

The application may have been reset when the computer is turned off
or in Standby mode. Exit and restart the application.

Содержание A790











































































































































Результаты поиска

Содержание A790

Отзывы:

Бренды по названию

Популярные бренды

API A790, Руководство по эксплуатации

Результаты поиска

Содержание A790

Отзывы:

Бренды по названию

Популярные бренды