manualshive.com logo in svg

API A790, Руководство по эксплуатации

Поделиться
Скачать
API A790 Скачать руководство пользователя страница 116

 

Troubleshooting 8-8 

The numeric keypad is disabled. 

z

 

Make sure that the 

Num Lock

 is switched on. (Check if the Num Lock 

Indicator 

N

 glows or not.) 

The external keyboard does not work. 

z

 

Make sure that the keyboard cable is properly connected. 

The USB mouse does not work. 

z

 

Make sure that the mouse cable is properly connected. 

The touchpad does not work, or the pointer is difficult to control 
with the touchpad. 

z

 

Make sure that the touchpad is clean. 

LAN Problems 

I cannot access the network. 

z

 

Make sure that the device driver is correctly installed. 

z

 

Make sure that the LAN cable is properly connected to the RJ-45 
connector and the network hub. 

z

 

Make sure that the network configuration is appropriate. 

z

 

Make sure that the user name or password is correct. 

WLAN Problems 

I cannot use the WLAN feature. 

z

 

Make sure that the mini PCI-E WLAN card is correctly installed. 

z

 

Make sure that the necessary driver(s) is correctly installed. 

z

 

Make sure that the WLAN feature is turned on (

Fn

+

F1

). 

Содержание A790











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды