manualshive.com logo in svg

API 8512 Series, Руководство по эксплуатации и установке

Поделиться
Скачать
API 8512 Series Скачать руководство пользователя страница 44

MANUAL IM635

 

Contacting Weinschel 

Page 44 

11. Contacting Weinschel

Please use the general information below to contact Weinschel for any inquires. 

Mail 

Weinschel 

5305 Spectrum Drive 
Frederick, MD 21703-7362 

U.S.A. 

Telefax 

1-301-846-9116 

Phone 

Toll Free: 1-800-638-2048 
Toll call: 1-301-846-9222 

Website 

http://weinschel.apitech.com/

 

E-mail 

[email protected] 

11.1.

 

Manufacturer Warranty 

PRODUCTS - Weinschel, a part of API Technologies Corp., warrants each product it manufactures to be free from 
defects  in  material  and  workmanship  under  normal  use  and  service  anywhere  in  the  world.  Weinschel’s  only 
obligation under this Warranty is to repair  or replace, at its plant, any product or part thereof that is returned 
with transportation charges prepaid to Weinschel by the original purchaser within TWO YEARS from the date of 
shipment. 

The foregoing Warranty does not apply Weinschel’s sole opinion to products that have been subject to improper 
or  inadequate  maintenance,  unauthorized  modifications,  misuse,  or  operation  outside  the  environmental 
specifications for the product. 

SOFTWARE  PRODUCTS  -  Weinschel  software  products  are  supplied  without  representation  or  Warranty  of  any 
kind.  Weinschel,  therefore,  assume  no  responsibility  and  will  not  accept  liability  (consequential  or  otherwise) 
arising from the use of program materials, disk, or tape. 

The Warranty period is controlled by the Warranty document furnished with each product and begins on the date 
of shipment. All Warranty returns must be authorized by Weinschel prior to their return.  

Weinschel’s Quality System Certified to: 

Содержание 8512 Series




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды