Apex Digital MASS FLOW METER Скачать руководство пользователя страница 9

Страница: 9 / 46

2020.07.24

•

REV. 2

• MASS FLOW METER OPERATING MANUAL

Option: Charging Your Portable Flow Meter

If you purchased a portable meter, it was fully charged at the factory, so

you can use it right away. Typical battery life of a fully-charged battery is 18

hours with a monochrome display or 8 hours with a TFT color display, when

the backlight is set to 10. Dimming the backlight will increase battery life.
The battery indicator on the right side of the Main Display reflects the

relative battery level. When the battery indicator is completely empty,

approximately 15 minutes of battery life remains. Please charge the flow

meter as soon as possible to maintain full device performance.
Charge the meter using the supplied USB cable (micro-B to type A) or a

similar cable. You may charge the flow meter using any USB outlet on a

computer or portable power supply, but charging will be fastest (approx-

imately 3.5 hours) when connected to the supplied 2.0A power supply.
The red indicator LED on top of the device lights up red to indicate that

the unit is charging. The red LED turns off when the battery is charged.
Your flow meter may be used while it is charging. A small lightning bolt

symbol (



) will appear to the right of the battery symbol while the device

is charging. If the battery has been fully depleted, you may need to charge

the flow meter for a full minute before the device can be turned on.

Warning:

The safe charging temperature range is 0–45°C

(32–113°F). If internal sensors detect temperatures

outside of this range, the battery will not charge.

95 – 100%
70 – 95%
50 – 70%
25 – 50%
5 – 25%
0 – 5%
Charging Indicator



PSIA

¤C

TARE

+13.60 +24.38 FLOW

+24.38

Flow Temp

¤C

Air



+16.670 +15.440

LPM

SLPM

Содержание MASS FLOW METER















































Результаты поиска

Содержание MASS FLOW METER

Отзывы:

Похожие инструкции для MASS FLOW METER

Бренды по названию

Популярные бренды

Apex Digital MASS FLOW METER, Руководство по эксплуатации

Результаты поиска

Содержание MASS FLOW METER

Отзывы:

Похожие инструкции для MASS FLOW METER

Бренды по названию

Популярные бренды