background image

Getting Started

Quick Start Guide

Setup

•  Connect your flow meter.

 Ensure that flow through 

your device will be in the same direction as the 

arrow on the flow body (usually left to right).

•  Tare your flow meter.

 Before you connect the flow meter, 

ensure that no gas is flowing through the device and select 

TARE FLOW

 from the Main Display. 

Note: 

Low-pressure-drop 

flow meters are sensitive enough to measure the lightest of 

breezes, so ensure that one end is plugged before taring.

•  Choose your engineering units. 

Press the button above or below 

any parameter to enlarge it in the middle of the display. If you select 

that same item a second time, you can change the engineering unit 

for that parameter. You can choose units for all of the parameters 

at once by selecting 

MENU 

 BASIC CONFIG 

 DEVICE UNITS

.

Operation: Flow Verification

•  Monitor live flow readings. 

You can monitor live readings 

of flow, pressure and temperature by viewing the screen. 

Readings are updated in real time. See 

page 17

.

•  Tare your flow meter 

before you begin another round of 

measurements. Ensure that no flow is passing through your meter, 

and select 

TARE FLOW

. See 

page 20

 for how to tare manually.

• 

(Optional) 

Capture a totalized reading. 

The totalizer 

option displays the total flow that has passed through the 

device since the last time the totalizer was reset. Press 

TOTAL/MENU 

to access the totalizer. Se

page 19.

Backlight

The monochrome display comes equipped with a backlight. 

To toggle its 

power, press the bottom-center button on the front of your device. 

For 

color displays, pressing this button will turn off the display to conserve power.

Maintenance and Care

• 

Flow meters will require no periodic cleaning for 

clean gases. Read more o

page 40

.

• 

Calibrate your flow meter annually.

Содержание MASS FLOW METER















































Отзывы: